16 Ton Forklift

HNF-160Rated load: 16,000 kgsLoad center: 900 mm?Operating weight: 24,000 kgs?Wheel base: 3,800 mm1, using speed limit valve and pressure selector valve, reduce the hydraulic system impact, can lower the mast to the ground when engine flame out 2, adopt double pump confluence working hydraulic system, greatly reduce fuel consumption, energy consumption. Hydraulic system equipped with oil radiator and back pressure protection device, ensure the machine heat balance 3, adopt double turbine hydraulic torque converter, stepless speed change, single lever control for the speed changing, easier for operation. 4, widely used in airports, ports, docks, stations, warehouses and other big working intensity occasions for loading and unloading, stacking and short-distance transportation 5, front axle adopt heavy duty type driving axle, enlarge size of axle housing, hub and bearing, spiral bevel gear and wheel planetary wheel deceleration increasing twist, steel structure bridge shell support, increase the load capacity and service life. 6, No spokes plate type rim, increase the bearing capacity of hub.How to repair the forklift driving axleThe forklift's axle housing is firmly fixed on the forklift’s frame. As the driving axle and the frame are rigidly connected, the driving axle undertakes the most weight when forklift handling cargos, and?when forklift working on uneven road or the unequilibrium of fork’s load ,driving axle will come to damages of bending, fracture, axle casing bearing hole wear and axle casing journal wear and so on.?The test and repair of Forklift driving axle housing’s bendingTest of the axle housing’s bending. Before testing, the first thing is to correct positive half axis and the flatness of the flat contact flange of the hub end, for eliminate the error of its round face runout. Then fixing the standard half-shaft on the driving axle housing, tightening bearing, testing the center of the left half axles and right half axles from housing’s inside to see whether bending or not. The difference between the two axes should less than 0.75mm.driving axle housing should be corrected when it over limit. During testing, the deformation should not be greater than the original bending deformation, and should keep the correction pressure for a period of time, in order to make axle housing a certain plastic deformation. If the deformation is too big, bending deformation more than 2mm, the correction can be done after preheat, but the heating temperature is not allowed to exceed 700 ?. It is better to avoid heating corrections for casted axle housing.ItemItem detailsUnitHNF-150HNF-160FeaturesRated LoadQ(t)1516Load centerc(mm)600900Wheelbasey(mm)35003500WeightWeightkg2200025000ChassisTyre Specs.:Front12.00-24-18PR12.00-24-18PRTyre Specs.:Rear12.00-20-18PR12.00-20-18PRTyres Qty,front/rear ? ? ?(X-drive wheels)4\24\2Wheel tread:Frontb10(mm)20602060Wheel tread:Rearb11(mm)23302330DimensionMast/carriage tilt angle(front/rear)Degree(°)6\126\12Mast height(fork lowering)h1(mm)36253625Mast lifting heighth3(mm)35003500Max.lifting heighth4(mm)53755375Height to head guard ? ? ? (height to cab)h6(mm)33653365Overall height(with forks)l1(mm)76407640Fork front vertical surface to the rear end of the vehiclel2(mm)58405840Overall widthb1/b2(mm)27502750Fork dimensions/e(mm)1800X180X901800X180X90Fork carriage widthb3(mm)23802380Mast min ground clearance ? ?(with load)m1(mm)265265Wheelbase center min ground clearance(with load)m2(mm)325325Min.Turning radiusWa(mm)58005800Travel speed ? ? ? ? ?(with load/without load)km/h26/3026/30PerformanceMax.lifting speed ? ? ? ? ?(with load/without load)mm/s250/260250/260Max.Lowering speed ? ? ? (with load/without load)mm/s430/330430/330TractionN1500015000Gradeablity ? ? ? ? ? (with load/without load)%20/2220/21Driving brakeHydraulic clamp discHydraulic ? clamp discEngine ?brand/modelOptional oneYuchai engineYuchai engineEngineYC6J175-T302 ?6.494L 129KW 2200rpmYC6J175-T302 ?6.494L 129KW 2200rpmOptional twoDongfeng CumminsDongfeng CumminsQSB6.7-C190 ?6.7L 142KW 2200rpmQSB6.7-C190 ?6.7L 142KW 2200rpmCylinder No.66OthersTransmission gears(Front/rear)2\12\1Attachments working pressurebar160160Attachments using oil amountl/min6060 ?
link:http://www.socma-forklift.com/heavy-duty-forklift/16-ton-forklift.html